The contact angle of nanofluids as thermophysical property.

Droplet volume and temperature affect contact angle significantly. Phase change heat transfer processes of nanofluids - suspensions containing nanometre-sized particles - can only be modelled properly by understanding these effects. The approach proposed here considers the limiting contact angle of a droplet asymptotically approaching zero-volume as a thermophysical property to characterise nanofluids positioned on a certain substrate under a certain atmosphere. Graphene oxide, alumina, and gold nanoparticles are suspended in deionised water. Within the framework of a round robin test carried out by nine independent European institutes the contact angle of these suspensions on a stainless steel solid substrate is measured with high accuracy. No dependence of nanofluids contact angle of sessile droplets on the measurement device is found. However, the measurements reveal clear differences of the contact angle of nanofluids compared to the pure base fluid. Physically founded correlations of the contact angle in dependency of droplet temperature and volume are obtained from the data. Extrapolating these functions to zero droplet volume delivers the searched limiting contact angle depending only on the temperature. It is for the first time, that this specific parameter, is understood as a characteristic material property of nanofluid droplets placed on a certain substrate under a certain atmosphere. Together with the surface tension it provides the foundation of proper modelling phase change heat transfer processes of nanofluids.

HRTEM Microstructural Characterization of ß-WO3 Thin Films Deposited by Reactive RF Magnetron Sputtering.

Though tungsten trioxide (WO3) in bulk, nanosphere, and thin film samples has been extensively studied, few studies have been dedicated to the crystallographic structure of WO3 thin films. In this work, the evolution from amorphous WO3 thin films to crystalline WO3 thin films is discussed. WO3 thin films were fabricated on silicon substrates (Si/SiO2) by RF reactive magnetron sputtering. Once a thin film was deposited, two successive annealing treatments were made: an initial annealing at 400 °C for 6 h was followed by a second annealing at 350 °C for 1 h. Film characterization was carried out by X-ray diffraction (XRD), high-resolution electron transmission microscopy (HRTEM), scanning electron microscopy (SEM), and atomic force microscopy (AFM) techniques. The ß-WO3 final phase grew in form of columnar crystals and its growth plane was determined by HRTEM.

Encapsulation, solid-phases identification and leaching of toxic metals in cement systems modified by natural biodegradable polymers.

Cement mortars loaded with Cr, Pb and Zn were modified by polymeric admixtures [chitosans with low (LMWCH), medium (MMWCH) and high (HMWCH) molecular weight and hydroxypropylchitosan (HPCH)]. The influence of the simultaneous presence of the heavy metal and the polymeric additive on the fresh properties (consistency, water retention and setting time) and on the compressive strength of the mortars was assessed. Leaching patterns as well as properties of the cement mortars were related to the heavy metals-bearing solid phases. Chitosan admixtures lessened the effect of the addition of Cr and Pb on the setting time. In all instances, chitosans improved the compressive strength of the Zn-bearing mortars yielding values as high as 15 N mm(-2). A newly reported Zn phase, dietrichite (ZnAl(2)(SO(4))(4)·22H(2)O) was identified under the presence of LMWCH: it was responsible for an improvement by 24% in Zn retention. Lead-bearing silicates, such as plumalsite (Pb(4)Al(2)(SiO(3))(7)), were also identified by XRD confirming that Pb was mainly retained as a part of the silicate network after Ca ion exchange. Also, the presence of polymer induced the appearance and stabilization of some Pb(IV) species. Finally, diverse chromate species were identified and related to the larger leaching values of Cr(VI).

Interaction of carboxymethylchitosan and heavy metals in cement media.

The performance of an etherified chitosan, carboxymethylchitosan (CMCH), when added to cement mortars doped with heavy metals, was assessed. In the presence of heavy metals (Cr, Pb, Zn) strong modifications of the fresh-state properties were evaluated. The addition of the polymer was seen to be useful in minimising some of these modifications, as those related to the setting time. A competitive mechanism for adsorption between the oxoanionic form of the metals and the carboxylate groups of the chitosan derivative was established. Studies on the metal chelating ability of the polymer and leaching from the hardened specimens showed scarce complexation under alkaline conditions, pointing to physical entrapment based on metal adsorption. However, significant chelation of metals was proved at near-neutral pH, suggesting the potential usefulness of the polymer as an agent for removing heavy metals from polluted waters and subsequently immobilizing them in cement mortars. Leaching tests carried out on polymer-metal complex-bearing samples showed a reduction in the amount of released Pb and Zn.

Adrenal response to tolbutamide-induced hypoglycemia in high altitude dwellers.

Adrenal response to tolbutamide-induced hypoglycemia was studied in 23 normal men born and living at high altitude (Morococha, Perú, 4,540 m) and compared to 23 men born and living near sea level. Fasting blood sugar was significantly lower in the high altitude dwellers (HAD) and this difference persisted throughout the test period. The blood glucose decrement at 30 min was significantly less in the HAD. Plasma cortisol response was significantly higher at 30 and 60 min in the HAD. Peak cortisol level occurred earlier in the HAD than in men living at sea level. The absolute cortisol increment at 30 min was significantly greater in the HAD.